Motorcycle clutch maintenance

[HEADER: Header-clutch.]

The clutch connects the motorcycle engine to the gearbox and ensures that power is transmitted controllably without loss to the rear wheel. The clutch is therefore a wearing part that requires occasional maintenance.

Here's how a motorcycle clutch works

The clutch functions on the principle of friction, and it therefore wears down with use - the greater the load the faster the wear. This occurs for example during traffic light starts with a high engine rpm and long slip phase. In this case, a large proportion of the engine's power is converted to heat and clutch disc wear instead of propulsion. The same applies essentially for the entire drive train, from the chain (or drive shaft) through to the back tyre.

Multiplate wet clutches have become the norm in modern motorcycles – with a few exceptions. The best way to describe this type of clutch is as a large, round, multi-decker sandwich, in which the friction plates are the ham, and the steel plates are the bread. These are pressed together by a pressure plate with the aid of multiple springs. Pressed together, they connect the engine and gears, which are disconnected again when you pull the clutch lever and the spring pressure on the discs is released.

The size, number and area of the discs and plates is precisely matched to the particular engine output. The upshot is that the rider can move off smoothly and without jerks, and engine torque transmission is reliable. Torsion springs in the clutch basket dampen the load-change reactions and ensure comfort. In addition, the clutch has a protective function if the engine stalls because the slip that arises protects the gears from excessive stress. Of course, a good clutch is only effective if actuation is working perfectly.

Hydraulic clutch operation

With a hydraulically operated clutch, essentially the same things need to be borne in mind as for disc brakes: The hydraulic fluid should not be more than 2-3 years old; there must be no air in the system; all seals must be working perfectly; the pistons must not stick (see DIY tip "Brakes"). No play needs to be set, as the hydraulic system is self-adjusting.

Mechanical clutch operation

It's a different story with mechanical actuation via cable. In addition to a teflon-lined or greased cable in perfect working order, setting the play is crucial. Too little play in a warm clutch causes linings to slip, resulting in them quickly becoming worn; plus overheating ruins the steel discs (blue discolouration, distorted discs). Too much play, on the other hand, can cause shifting problems. The stationary bike will tend to take off before the clutch lever is released, and it is hard to put it into neutral – namely because the clutch does not properly disengage.

This can also happen if the steel discs have become distorted! However, jerky engagement and disengagement of the clutch usually indicates that the clutch basket and drive plate have had it On most motorcycles, it's possible to overhaul the clutch and change the linings without removing the engine.

So, if you're not afraid of getting your hands dirty and have a certain degree of DIY ability, you can do this yourself and save a good deal of money.

But remember: A bad job can cause damage or even an accident! So care and the right tools are indispensable!

Maintenance work on the clutch

Before you begin, first check in your motorcycle's workshop manual whether you need special tools. Thankfully, motorcycles like the '94 model CB 500, where the clutch pressure plate is retained by a special nut, are the exception rather than the rule. Find out about tightening torques and particular installation and setting procedures that are unique to your bike. Also protect your garage floor from oil spills and leaks before you drain the engine oil into a suitable container. Of course, the best time to do this is when the engine is warm. While it cools, start making the clutch cover accessible, and clean any dirt from the area around it. A footrest will usually have to be removed, and sometimes a kickstarter. Also remove any covers from the clutch release mechanism with its adjusting device. And now it's down to business:

Removing the clutch cover

[IMAGE: clutch.]

Have tools ready – cover floor – drain oil

Unscrew and remove the cover screws in stages using a suitable tool. Screws that have been machine-tightened or painted over can be very tight. In that case, a tap on the head of the screw usually helps. The best tool for cross-head screws is an impact screwdriver.

[IMAGE: cover.]

Undo cover

To release the cover from its dowel pins, take the plastic end (!) of the Vario hammer and carefully tap around the cover until it comes away. Important: Only use a screwdriver for leverage if there are suitable gaps or lugs on the cover and housing! Never try to force the screwdriver between the sealing surfaces, as this will cause irreparable damage! If the cover stubbornly refuses to come away, check if you have forgotten a screw! Generally, the gasket sticks to both surfaces and tears, so it must be replaced. Then remove the residue using Procycle Gasket Remover or brake cleaner and a gasket scraper, taking care not to damage the sealing surface. Fit a new gasket later. Also put the dowel pins somewhere safe!

Dismantling the clutch

[IMAGE: clutch.]

Remove clutch

You are now looking at the clutch basket. To get at the inner workings, you must first remove the clutch pressure plate. This usually means undoing a certain number of screws or, in rare cases, a central nut. Always loosen the screws in stages (approx. 2 revolutions each) working crosswise! If necessary, you can stop the clutch basket from turning by engaging first gear and locking the foot brake. Once the screws are unscrewed, you can remove the compression springs and the pressure plate. Now the steel plates and friction discs can be removed. Please set down everything on a clean sheet of newspaper or a cloth so that you can remember the order in which to reinstall them.

Checking the clutch components

[IMAGE: check parts.]

Check parts

Clutch springs show signs of fatigue and shrinkage with time. For this reason, measure the length and compare with the wear limit in your workshop manual. Clutch springs are relatively low-cost (approx. 15 euros). Since weak/worn springs cause clutch slippage, we recommend you change them if in any doubt! The steel plates between the friction discs can warp due to heat, in which case they will usually show a bluish discolouration. You can check with a feeler gauge and surface plate. Or instead of a surface plate, you can use a pane of glass or mirror plate. Gently press the disc against the pane of glass and try to measure the play between disc and glass at various points using the feeler gauge. Slight distortion (up to approx. 0.2 mm) is tolerable. Please see your motorcycle manual for the exact value. Discoloured and distorted discs must be replaced with OEM parts. The same applies to heavily worn clutch baskets and internal drive plates. Minor nicks on the sides of the lining guides can be smoothed with a file. This is time-consuming but saves money. To ensure that no filings fall into the engine, the parts must be removed. Undo the central nut to remove the clutch basket, while gripping the hub with a special tool. For further details on this, please refer to your manual. Also check the condition of the damper on the clutch basket. Rattling sounds when the engine is running are a sign of damage as a result of wear. While the basket is allowed to have a little play when installed, it should not feel soft and worn overall when you turn it and jiggle it firmly.

Assembly and adjustment

[IMAGE: clutch.]

Install clutch

Once you have decided which parts need to be replaced with new ones, you can begin assembly. Remove wear residue and dirt from the used parts using petroleum ether or brake cleaner. Now put back the cleaned and oiled parts in reverse order. Please refer to the workshop manual again to refresh your memory. Pay close attention to any markings on the components that indicate a certain position! If you have not removed the clutch basket, the job is relatively easy: first insert the clutch discs, starting and ending with a friction disc (never a steel plate). Then put on the pressure plate and fit the springs with the screws (a little pressure is usually required). When positioning the pressure plate, pay attention to any markings! Finally, tighten the screws in stages and in a criss-cross pattern. If your workshop manual specifies a torque, you should always use the torque wrench. Otherwise tighten with care. Do not use force, as the threads sit in quite slender lugs on the inner clutch hub.

[IMAGE: adjust play.]

Adjust play

With a cable-actuated clutch, adjusting the clutch play is key to the outcome. This can be done via an adjustment screw located in the centre of the clutch basket, or on the opposite side of the engine or, in the case of a release mechanism, in the clutch cover. Always follow the manufacturer's instructions.

[IMAGE: cover.]

Fit the cover – tighten screws in increments

After checking that the sealing surfaces are clean and fitting a new gasket, you can put the clutch cover back on. Don't forget the dowel pins! Position the screws. First screw them in loosely, then tighten them with care or use a torque wrench, as directed by the manufacturer.

[IMAGE: readjust cable.]

Readjust cable

For cable adjustment, ensure that there is approx. 4 mm of play in the clutch lever before applying a load to the lever. The hollow screw should not be rotated too far out of its seat!

Do not forget engine oil

[IMAGE: fill with oil.]

Fill with oil

Now you can put the oil in. Make sure the oil-drain plug is secure! Then install the footrest, kickstarter, etc. and release the brake and rear wheel if necessary. Just to be safe, before you take her for a proper spin, recheck your work: with the brake and clutch pulled, start the engine in neutral, and then gently engage first gear. If you can now accelerate without any catching or slippage, you have done a good job and can look forward to plenty of easy riding again!

Download this tip

[IMAGE: Download this tip.]

Simply download and use it offline.

[IMAGE - The Louis mechanics crew.]

The Louis Technical Centre

Problems getting spare parts? Or maybe you've got a technical question about your motorcycle or an accessory The Louis Technical Centre can help! Remember to quote all the necessary details of your vehicle – better still, send us a copy of your registration document.

We will get back to you as quickly as possible!

So: send us your technical problem!

Please note!

These tips for DIY mechanics contain general recommendations that may not apply to all vehicles or all individual components. As local conditions may vary considerably, we are unable to guarantee the correctness of information in these tips for DIY mechanics.

Thank you for your understanding.

German Version

Louis DIY Mechanic Manual

[IMAGE - Louis DIY Mechanic Manual.]

The printed version

The big Louis DIY mechanic manual available in a printed version: in color and practical A4 format at cost price.

Buy now!